STACKMASTER TX12 SPECIFICATIONS
Standards
IEEE 802.3u 100BASE-TX
Class 1 (stacked)
Class 2 (unstacked)
Physical
Dimensions
17’ x 10’ x .1.8’
(438 mm x 255 mm x 45 mm)
Shipping Weight
StackMaster™ TX12
100BASE-TX 12-Port Stackable Hub
(SMHB-E-TX-12)
9 lbs
(4.1 kg)
Input Power
Internal universal input; 100–240VAC, 50/60 Hz, 53W
AC Input Cord:
TN PN
3344
3344
3347
3348
3349
Requirement
120 volts, 60 hertz
100 volts, 50-60 hertz Japan
230 volts, 50 hertz
240 volts, 50 hertz
240 volts, 50 hertz
Location
USA/Canada/Mexico
33010.B
Europe
Australia
United Kingdom
For assistance in installing, using, or
maintaining the TRANSITION Networks
StackMaster™ TX12 100BASE-TX 12-Port
Stackable Hub, contact TRANSITION
Networks Technical Support at:
MTBF
50,000 hours
Environment
Temperature:
0-50°C (32° to 122° F )
Humidity
Altitude
10-90%, non condensing
0-10,000 feet
(800) 260-1312
Warranty
or contact your local distributor.
Lifetime
17
FAST ETHERNET (IOOBASE-X)
CABLE SPECIFICATIONS
Table of Contents
Due to the limited collision domain in 100BASE-X, use the shortest
cables possible to make a connection between any two devices.
Where collisions are not a consideration (full duplex), longer
cable may be possible.
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
The StackMaster TX12 Hub . . . . . . . . . . . . . . . . . . . . . . . . . .1
StackMaster TX12 Hub Features . . . . . . . . . . . . . . . . . . . . . . . .1
Networking the StackMaster TX12 Hub . . . . . . . . . . . . . . . . . . .2
StackMaster TX12 Hub Connectors and Status LEDs . . . . . . .3
RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SCSI Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Effective cable distances are determined by ambient RF noise and
by signal loss in the cable. Since fiber has low signal loss/meter
and invulnerability to RF noise, fiber is the preferred medium for
extending distances.
100BASE-FX Cable and Connector Specifications
The physical characteristics of the 100BASE-FX cable must meet or
exceed IEEE 802.3 100BASE-FX specifications.
2 SITE CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . 4
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking 12-Port Stackable Hub . . . . . . . . . . . . . . . . . . . . .5
Installing StackMaster™ TX12 in 19-inch Rack . . . . . . . . . . .6
Optionally Cascading 12-Port Stackable Hubs . . . . . . . . . . . .7
Using Port 12 to Cascade Two Hubs . . . . . . . . . . . . . . . . . . . . .7
Using SCSI Connectors to Cascade Stacked Hubs . . . . . . . . . . .8
Connecting 100BASE-TX Cable . . . . . . . . . . . . . . . . . . . . . . .9
Connecting Power to StackMaster™ TX12 . . . . . . . . . . . . . .10
100BASE-FX CABLE SPECIFICATIONS
Fiber Optic Cable Recommended:
62.5 / 125 µm multimode fiber
100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Optional:
Fiber Optic Transmitter Power:
Average power:
-19.0 dBm
4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Fiber Optic Receiver Sensitivity:
Average sensitivity:
-33.5 dBm
5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Technical Support Contact . . . . . . . . . . . . . . . . . . . . . . . . .12
Bit error rate:
≤10-10
2000 meters (6500 feet)
Maximum Cable Distance:
100BASE-FX CONNECTOR CHARACTERISTICS:
WARRANTY STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CABLE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
STACKMASTER TX12 HUB SPECIFICATIONS. . . . . . . . . . . 17
The 100BASE-FX connectors are standard ST connectors.
SC connectors are available.
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
i
15
100BASE-TX 12-Port Stackable Hub
The sole purpose of this remedy shall be provided the customer with the replacement or
repair of non-conforming goods in the manner described in this Warranty statement. This
exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is
willing and able to repair or replace the defective item(s) or refund the purchase price.
1. INTRODUCTION
This guide is intended for the system or network administrator
responsible for installing and monitoring a TRANSITION Networks
StackMasterTX-12 100BASE-TX 12-Port Stackable Hub. A working
knowledge of local area network (LAN) operations, including
familiarity with communications protocols used on interconnected
LANs, is assumed.
TN reserves the right to inspect products claimed to be defective under warranty either at the
customer’s location or at TN’s plant. TN assumes no liability for liability charges incidental
to the adjustment, service, repairing, removal or replacement of the product, or other costs,
or the expense of repairs made outside of its factory, except when made with TN’s prior
written consent. Additionally, Transition Networks reserves the right to charge for all testing
and shipping incurred, if after testing, a return is classified as “No Problem Found”.
TN’s total liability in connection with the products and their installation to all persons and
from all causes in the aggregate, whether in contract, tort, or strict liability, shall not exceed
the amount paid to TN for the product directly related to the alleged damage. However, in
no event shall TN have any liability to a customer or any third party for products
manufactures according to the customer’s specifications.
The StackMaster TX12 Hub
The StackMasterTX-12 100BASE-TX 12-Port Stackable Hub (SMHB-
E-TX-12) is a Fast Ethernet repeater designed to meet IEEE 802.3u
100BASE-TX standards.
C. Return Procedure
The customer must follow this procedure for the return of defective items:
1. Locate the serial number(s) of the item(s) to be returned.
2. Determine the date the item(s) was received.
3. Contact Transition Networks Technical Support to determine if the problem can be
corrected on site.
If not, and the product is covered by warranty, then:
•
•
•
Call the distributor directly or contact TN.
StackMaster TX12 Hub Features
Request a Return Material Authorization (RMA).
Ship the item, prepaid in original packaging to Transition Networks at the above
address.
Include the RMA number on the outside of the carton and/or on the Packing List.
Include a copy of the RMA form.
•
Twelve RJ-45 100BASE-TX ports for Fast Ethernet
connectivity
•
•
•
•
Port #12 provides StackMaster TX12-to-StackMaster TX12
MDI/MDI-X uplink option
Include a copy of the original invoice or packing list (if possible) to expedite
processing.
•
•
The item(s) may be shipped by the customer or the distributor.
Transition Networks will repair or replace the unit, at TN’s discretion, and cover the
cost of the return freight to the distributor or to the customer, whichever requested
the RMA number.
•
•
•
•
•
Optional cascading of hubs using SCSI connectors at back
19-inch rack mountable
If the item(s) was received more than five years ago, or if the item(s) is no longer covered by
warranty for other reasons, then:
Auto partitioning of ports with excessive collisions
Fully automatic preamble regeneration
Internal universal input power supply
•
•
•
Call the distributor or contact TN.
Request a Material Repair Authorization number (MRA).
Ship the item(s), prepaid, in the original packaging to Transition Networks at the
above address.
•
•
•
•
•
Include the MRA number on the outside of the carton add/or on the Packing List.
Include a copy of the MRA form.
Include a copy of the original invoice or packing list (if possible) to expedite processing.
Only the customer (end-user) may send the items(s) to TN.
TN will contact the customer after the item(s) have been received, inspected, and a
cost estimate of the repair determined.
•
The repair charges may be billed, with customer’s approval, though the distributor, or
on a prepaid or C.O.D. basis directly to the customer. The charges will include the
cost of shipping.
The return authorization numbers are valid only for 90 days from the date issued.
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
14
1
100BASE-TX 12-Port Stackable Hub
Warranty Statement
Networking the StackMaster TX12 Hub
A. Five Year Warranty
Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with
the exception of power supplies and fans that TN warrants for two years) will be free from
defects in materials and workmanship, and will be in conformity with TN’s specifications.
Use the StackMaster TX12 100BASE-TX 12 port stackable hub alone
to provide twelve RJ-45 Fast Ethernet port connections.
TN’s warranty on products manufactured by or assembled for TN in accordance with a
customer’s specifications, is a five-year warranty that the goods conform to such
specifications.
Up to 100 meters
The warranty is invalidated if the goods have been subject to alterations, misuse, accident,
Acts of God (e.g., damage by floods, lightning strikes, Etc.), tampering, improper
maintenance, improper installation, or abuse. If the user is unsure about the proper means
of installing or using the equipment, contact TN’s free Technical Support or Network
Design Services, which can be reached by:
Cascade two StackMaster TX12 hubs throough the uplink port to
provide twenty-two RJ-45 Fast Ethernet port connections.
Telephone
Fax
1.800.LAN.WANS or 612.941.7600
612.941.2322
E-mail
Internet
THE ABOVE WARRANTY IS EXCLUSIVE AND EXTENDS ONLY TO PRODUCTS
ASSEMBLED BY TRANSITION NETWORKS, INC. TO THE EXTENT PERMITTED BY LAW,
TN DOES NOT MAKE AND DISCLAIMS ALL OTHER WARRANTIES, EXCEPT TITLE,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
DESCRIPTION, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT, AND ANY WARRANTY BASED UPON PRIOR WRITTEN OR ORAL
REPRESENTATIONS REGARDING SUCH PRODUCTS MADE BY TN, ITS EMPLOYEES,
AGENTS, OR REPRESENTATIVES.
Up to 100 meters
Up to 5 meters
B. Limitations and Exclusions
If the customer believes any goods sold by TN are defective and within the warranty period,
the following general procedure will be followed:
1. Locate the serial number and delivery date of the item(s).
2. Notify TN within the warranty period.
Up to 100 meters
3. TN will promptly issue a return authorization form for the goods.
4. Upon receiving the form, the customer will promptly return the item(s) at customers
own expense, shipped prepaid, to the distributor from which it was purchased, or
directly to TN.
TN will only accept goods for return if the following conditions have been met:
1. A return form is obtained from TN.
Cascade up to six StackMaster TX12 hub, using SCSI cascade
connectors at the back, to provide seventy-two RJ-45 Fast Ethernet
port connections.
2. The freight charges have been prepaid by the customer.
3. Goods are re-packed in their original packaging.
Up to 100 meters
If under warranty TN shall, at its option, (1) repair the goods free of charge (2) replace the
goods free of charge, or (3) accept the return of the item(s) and credit the current price to
the reseller (within 90 days of purchase), or (4) if the goods are not under warranty, will
repair the item(s) at a minimum charge of USD $200 (two hundred U.S. dollars) per item.
THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. IN NO EVENT
SHALL TRANSITION NETWORKS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF ANY
CONDITION OF SALE, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY,
CONTRACT, OR OTHERWISE AND IRRESPECTIVE OF WHETHER TN IS INFORMED BY
CUSTOMER OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE OF THIS SALE.
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
2
13
100BASE-TX 12-Port Stackable Hub
StackMaster TX12 Connectors and Status
Indicators
5. MAINTENANCE
WARNING: DO NOT, UNDER ANY CIRCUMSTANCES,
open and attempt to repair the StackMaster TX12 100BASE-
TX 12-Port Stackable Hub. Failure to observe this warning
could result in personal injury or death from electrical
shock.
RJ-45 Connectors
Twelve (12) 100BASE-TX RJ-45 connectors are located at the front of
the StackMaster TX12. The RJ-45 jacks support connection to
Category 5 shielded or unshielded 100 ohm twisted pair 100BASE-TX
cable.
NOTE: Failure to observe the above warning will immediately void
the warranty.
SCSI Connectors
Two (2) SCSI connectors are located at the back of the StackMaster
TX12 for optionally cascading hubs.
Fault Isolation
If two network devices fail to communicate through the
StackMaster TX12, consider the following:
Power Connector
•
Are the LEDs described in the previous section functioning
properly?
An external power connector is located at the back of the StackMaster
TX12.
•
•
Do network devices have Link Integrity enabled?
Status LEDs
Do network devices communicate when the StackMaster
TX12 is not installed between them?
Status LEDs are located at the front of the StackMaster TX12.
POWER
Illuminated green: Hub powered ON.
•
•
Is flat or “silver satin” wire used in site internal wiring?
UTILIZATION
Iilluminated green 1%, 8%, 16%, 32%, or 64%
network activity
Are internal wiring patch cords, punch down blocks, and
wall jacks properly pinned or configured?
COLLISION
LINK/ACTIVITY
ERROR
Illuminated amber: Collision detected during data
transmission on ANY port.
•
Are network interface cards properly configured?
Illuminated green: Port link established.
Flashing green: Data being received.
Technical Support Contact
For assistance in fault isolation and in maintaining the StackMaster
TX12 100BASE-TX 12-Port Stackable Hub, contact:
Flashing yellow: Error detected on port.
Illuminated yellow: Port partitioned and isolated.
Technical Support
(800) 260-1312
or your local distributor.
Download from Www.Somanuals.com. All Manuals 1Se0a0rcBh AAnSd ED-oTwnXloa1d2. -Port Stackable Hub
StackMaster™ TX12
12
3
4. OPERATION
2. SITE CONSIDERATIONS
The StackMaster TX12 normally requires no intervention beyond
occasionally monitoring the Power and Status LEDs.
The site for the StackMaster TX12 hub must provide:
•
•
•
•
AC power outlet for each hub
Adequate ventilation
Standard environmental conditions
Isolation from electrical noise, including radio transmitters
and broadband amplifiers, motors, high power electrical
lines, or fluorescent light fixtures.
Additionally:
•
The twisted pair cables should not run in the same conduit
with power line cables
•
•
Phone lines should be separated from data cables
Flat or “silver satin” wires should not be used.
And:
•
Since the StackMaster TX12 functions as an Ethernet
Repeater, the entire installation should comply with the IEEE
Ethernet 802.3 specification.
Status LEDs
Status LEDs are located at the front of the StackMaster TX12.
POWER
Illuminated green: Hub powered ON.
UTILIZATION
Iilluminated green 1%, 8%, 16%, 32%, or 64%
network activity
COLLISION
LINK/ACTIVITY
ERROR
Illuminated amber: Collision detected during
data transmission on ANY port.
Illuminated green: Port link established.
Flashing green: Data being received.
Flashing yellow: Error detected on port. OR
port partitioned and isolated.
Download from Www.Somanuals.com. All Manuals 1Se0a0rchBAAndSEDo-wTnXloa1d.2-Port Stackable Hub
StackMaster™ TX12
4
11
Connecting Power to StackMaster TX12
To power ON the StackMaster TX12:
3. INSTALLATION
NOTE: StackMaster TX12 Link Integrity cannot be disabled. All devices
connected to the StackMaster TX12 MUST have link functions enabled.
1. Locate the power receptacle on the back of the StackMaster
TX12.
To install the StackMaster TX12:
•
•
•
•
•
Unpack the StackMaster TX12 Hub.
2. Connect the StackMaster TX12 power connector end of the
power cord to the StackMaster TX12.
Install StackMaster TX12 on shelf or in rack
Optionally cascade StackMaster TX12 hubs
Connect 100BASE-TX cable to StackMaster TX12
Connect the StackMaster TX12 to power.
3. Connect the external power connector end of the power cord
to external AC power.
Direction is provided in the pages that follow.
NOTE: After power is supplied to the StackMaster TX12, the green
Power LED is illuminated.
Unpacking the StackMaster TX12
The StackMaster TX12 packing contents should include the following:
Item
Part Number
StackMaster TX12
Power Cord
SMHB-E-TX-12
3344, 3347, 3348, 3349, or 3523,
(depending upon power configuration
in country where installed)
SCSI Connector
User’s Guide
33010
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
10
5
Connecting 100BASE-TX Cable
Installing StackMaster TX12 in 19-inch Rack
To connect 100BASE-TX Cable to StackMaster TX12 RJ-45 connectors:
NOTE: Optionally, the StackMaster TX12 can be installed on a table or
other flat, stable surface.
1. Locate or build 100BASE-TX cables with the following
characteristics:
NOTE: The StackMaster TX12 is shipped with attached brackets for
standard 19-inch rack installation. Rackmount screws and clip nuts are
NOT provided.
•
•
•
803.2 compliant (See page 15)
cable length less than 100 meters
male RJ-45 plug connectors installed at both ends of
cable.
To install the StackMaster TX12 in 19-inch rack:
2. Connect male RJ-45 plug connector at one end of 100BASE-
TX cable to StackMaster TX12 RJ-45 jack connector.
3. Connect male RJ-45 plug connector at other end of 100BASE-
TX cable to terminal device RJ-45 jack connector.
Up to 100 meters
1. Locate four (4) screws (and clip nuts, if necessary) for each
StackMaster TX12 to be installed.
2. Carefully align the StackMaster TX12 between the 19-inch rack
mounting rails at the installation position.
3. Install two screws through right front bracket and two screws
through left front bracket, using clip nuts if necessary.
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
100BASE-TX 12-Port Stackable Hub
6
9
Optionally Cascading 12-Port Stackable Hub
Using SCSI Connectors to Cascade Stacked Hubs
Up to six StackMaster™ TX12 hubs can be cascaded by installing SCSI
connectors at the back of the StackMaster™ TX12 stack.
Using Port 12 to Cascade Two Hubs
Two StackMaster™ TX12 hubs can be cascaded using the two
connections at the front of each hub that are labelled ‘Port 12’.
To cascade a StackMaster™ TX12 stack:
To cascade two StackMaster TX12 hubs:
Up to 5 meters
1. Locate or build 100BASE-TX cable with the following
characteristics:
•
•
•
803.2 compliant (See page 15)
cable length less than 5 meters
NOTE: Install the SCSI cable by carefully pressing the cable
connector against the StackMaster™ TX12 connector until the
connectors snap into place.
male RJ-45 plug connectors installed at both ends of cable.
2. Connect male RJ-45 plug connector at one end of 100BASE-TX
cable to Port 12 connector marked MDI-X.
1. At back of stacked StackMaster™ TX12 units to be cascaded,
connect a SCSI cable to the BOTTOM SCSI connector on the
top StackMaster™ TX12 hub.
3. Connect male RJ-45 plug connector at other end of 100BASE-
TX cable to Port 12 connector marked MDI.
2. Connect the SCSI cable to the TOP SCSI connector on the next
StackMaster™ TX12 hub.
3. Connect another SCSI cable to the BOTTOM SCSI connector
on that StackMaster™ TX12 hub, as shown above.
4. Connect the SCSI cable to the TOP SCSI connector on the next
StackMaster™ TX12 hub, as shown above.
5. Continue connecting SCSI cables by repeating steps 3 and 4
until the entire StackMaster™ TX12 stack is cascaded.
NOTE: The open SCSI connectors at the top and bottom of the
StackMaster™ TX12 stack do NOT require termination.
StackDMowanslotaedrf™romTWXww1.2Somanuals.com. All Manuals Search And Download.
100BASE-TX 12-Port Stackable Hub
8
7
|